I Can Mend a Hole in a Back Pocket Three Different Ways. This is My First Favorite!

Just as I promised, here’s my other favorite way to mend a hole in a back pocket!

I’ve got two favorite ways to mend a hole in a back pocket (and a third way that I don’t like as much but that also works great!), and recently, my kid presented me with a pair of pants that had a hole in each back pocket, allowing me to put my two favorite methods into direct competition. She keeps her phone in one back pocket and her wallet in the other, so as a bonus, the holes are nearly symmetrical and nearly identical. It’s the perfect scenario for an experiment!

With the kid’s permission, I mended one hole with a patch on the outside, and one hole with a patch on the inside. Both methods require the same materials and take approximately the same amount of time. They’re also both very easy, with the trickiest part of the outside patch the folding and creasing, and the trickiest part of the inside patch its placement. I showed you how to do the outside patch last week, so this time, let’s discuss the inside patch!

This inside patch method involves just what it says: instead of patching the outside of the hole, you’ll be patching the inside of the hole. The patch will still show through the hole, but will be far less visible than a patch outside the hole would be. What WILL be pretty visible–depending on thread color!–is all the reinforcement stitching that stabilizes the hole and keeps the patch attached. Depending on your goals and your skill set, the stitching can be messy (but effective!) or highly decorative.

Here’s what you need to complete this mend:

Materials

• patch. Match the weight of the existing fabric, but otherwise the choice is up to you! If you match the patch fabric very well, the patch will be quite inconspicuous, but a visible patch can be really cute, too.
• thread. This is the most visible part of this mend, so your choice is very important here. Well-matched thread color will be nearly invisible, but you also can do such cute things with visible mending.
• cutting and sewing supplies. This is a hand-sewing project, so requires a hand-sewing needle and thread scissors. Pins are helpful, but optional. You don’t particularly need an iron, and you definitely don’t need fusible interfacing, although you can use it it–just keep it away from the hole itself!

Step 1: Prep and place the patch.

Cut the patch to be wider than the hole in both length and width, then insert it into the back pocket and place it behind the patch. This is the trickiest part of the whole project, since you have to make sure that the patch sufficiently overlaps the hole, and you have to do it mostly by feel.

Once the patch is in place, you can pin it to make sure it stays secure, but it should stay very well even without pinning. If you do pin, make sure that you haven’t caught the inside of the pants with your pin–the last thing you want to do is sew your pocket shut!

Step 2: Hand-stitch the patch in place.

This is the fun–and a little bit time-consuming!– part!

Thread your needle with the thread you’ve chosen, and then simply begin to stitch the patch to the pocket. Focus on stabilizing the hole, particularly the raw edges of the hole, but stitch over the entire patch area, the more stitches, the better. Every stitch that you put in, however messily, strengthens the fabric and reinforces the mend.

When you’re finished hand-sewing, turn the pocket inside-out and trim away any excess patch material, being careful not to cut through any of your stitching.

I asked my kid for her final opinion (since these are her pants, lol!), and she said that she liked the look of the inside patch better, but thought that the outside patch was fine, too. I will say that the inside patch seems less visible from a distance, but these grey jeans were tricky to match, and if I’d been able to match the outside patch fabric perfectly to the pants it might well be just as inconspicuous.

For what it’s worth, I volunteer monthly with my local public library to mend items that patrons bring in, and I use the inside patch method almost exclusively during Mending Days. It’s especially easy when someone needs a mend in the knee or thigh, since I can use the zigzag stitch on my sewing machine to do alllll that stitching in just a few seconds. If it’s a rip that I’m mending, not a hole, often the patch isn’t visible at all afterwards, and if I happen to have a thread color that perfectly matches the fabric, the stitching is barely visible, as well.

Which method do YOU prefer?

P.S. Want to follow along with my craft projects, books I'm reading, dog-walking mishaps, road trips, and other various adventures on the daily? Find me on my Craft Knife Facebook page!